中国(上海)自由贸易试验区临港新片区老芦公路536号
021-57525860·13162862074
首页/产品目录/无转子硫化仪
16 / 16 · 产品线

无转子硫化仪Rotorless Rheometers

无转子硫化仪在密闭模腔内对胶料施加小幅振荡剪切应变,记录转矩随时间的変化,得到焦烧时间、正硫化时间与硫化平坦期等关键工艺参数。

5款机型
0类型
GBISO · ASTM
48h技术响应
5 款机型
共 5 款机型 · 产品线⚡ 快速选型向导⌕ 产品选型中心¥ 报价申请与选型方案▤ 选型方案↓ 选型方案书
没有匹配的机型,换个关键词或直接联系工程师。

技术资料

六份技术文件,覆盖原理到验收

行业案例

典型检测工况,以及本产品线对应的解决思路。

01
工况轮胎胶料
检测难点硫化曲线与 t90
解决方案145℃,ASTM D5289
结果出具检测报告;按标准核验示值误差与重复性。
02
工况密封件
检测难点门尼焦烧时间
解决方案120℃,转子法
结果出具检测报告;按标准核验示值误差与重复性。
03
工况胶管
检测难点硫化返原评价
解决方案多转速对比
结果出具检测报告;按标准核验示值误差与重复性。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

产品原理

从物理效应到测量结果,讲清设备的工作原理。

压头物镜试样光源数据处理
原理要点
  1. 模腔上下模以设定频率(如 1.7Hz)与振幅(±0.5°)相对摆动,胶料在腔内承受剪切变形,反作用转矩由扭矩传感器采集
  2. 随交联密度上升转矩增大,曲线给出 ML(最低转矩)、MH(最高转矩)、ts1/ts2(焦烧时间)、t10/t50/t90(硫化时间)
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

动图流程

标准作业顺序,并标出最易引入误差的关键步骤。

01取样并称量(按体积) →
02放入模腔 →
03合模升温至试验温度 →关键控制点
04振荡采集转矩曲线 →关键控制点
05软件自动读取 ML/MH/ts/t90 →
06输出报告

参考耗时 — 单件典型耗时 3–15 分钟;高亮步骤是测量误差的主要来源。

常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

标准规范

涉及方法、检定与验收的国家标准与国际标准。

标准编号适用范围
GB/T 16584橡胶 用无转子硫化仪测定硫化特性
ISO 6502橡胶 硫化特性的测定 无转子硫化仪法
GB/T 1233未硫化橡胶 初期硫化特性的测定
常见问题
Which standards apply?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

选型方案

按工况对应推荐系列,再与工程师确认具体配置。

工况推荐系列选型理由
常规配方与质控选标准型(±0.5°、1.7Hz)以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
研究型选可变频率/应变机型以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
需与门尼黏度联测选带门尼模块以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
高温快检选 200℃ 以上高温型。以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

检测方法

取样、制样、检测、复核与验收判据。

标准作业流程
  1. 用标准胶(如 NR 标准胶)校验转矩示值与温度
  2. 模腔温度均匀性需满足 ±0.3℃,试验前必须做空白(无料)基线校准
验收判据

用标准块间接检定:工作面均布不少于 5 点,示值误差与重复性需满足相应检定规程。

注意事项

班前用标准块校验,保持压头与试样表面清洁,测量系统定期用标准刻线尺校准。

常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
咨询热线