点击查看大图RQMC030-ZJPX300
精度1″ 物镜焦距 300mm。
- ✓原厂校准证书
- ✓12 个月质保
- ✓全国安装调试
- ✓支持非标定制
产品介绍
MC030-ZJPX高速系列光电自准直仪使用高精度成像系统搭配高速光电探测器,在保证测量精度的同时,采样频率达到100HZ、200HZ、500HZ甚至更高,主要应用于各种微小角度的动态监测或者产品几何精度的在线检测。
技术参数
型号RQMC030-ZJPX300-2350HZ
物镜焦距300mm
通光口径48mm
光轴中心高78mm
视场范围(X、Y)3000*1800″
分辨率0.1″、0.01″、0.001″、0.0001″可调 (arc sec. 角秒 )
示值精度±1000″≤ ±1″
采样频率全视场最高 1000HZ 可调
光源类型625nm 半导体 LED(可定制)
探测器类型高速面阵光电探测器
第三方通讯RS232 串口
接口方式CoaXPress-12
显示方式基于普通 PC 的软件显示
电源DC12V1A
仪器尺寸(长 * 宽 * 高)385*100*115mm
重量4.28kg
从物理效应到测量结果,讲清设备的工作原理。压头物镜试样光源数据处理原理要点光源经分划板(十字丝)后由物镜准直为平行光束,射向被测反射镜反射镜倾斜 α 角时,反射像在焦面上偏移 f·tan2α,由高分辨率图像传感器采集偏移量并换算为角度值双轴机型在 X、Y 两个方向同时成像,一次装夹即可完成二维角度测量常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement; we provide a test report together with the recommended configuration.相关机型RQYRMAT1510RQYRMAT1815RQYRMAT3025RQYRMAT3030获取报价 →参数对比 →咨询工程师 →
技术规格
选型指南
- 按工况对应推荐系列,再与工程师确认具体配置。工况推荐系列选型理由按精度选0.1″–0.5″ 用于计量室与精密装配,1″ 用于车间现场以上参数仅供参考,最终配置、价格与交期以正式报价单为准。按测量距离选 5m / 10m / 20m / 30m / 50m以上参数仅供参考,最终配置、价格与交期以正式报价单为准。需要二维同时测量选双轴机型以上参数仅供参考,最终配置、价格与交期以正式报价单为准。动态跟踪(转台、振动台)选高速采样机型以上参数仅供参考,最终配置、价格与交期以正式报价单为准。大平面检测选大视场系列。以上参数仅供参考,最终配置、价格与交期以正式报价单为准。常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard
- an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement
- we provide a test report together with the recommended configuration.相关机型RQYRMAT1510RQYRMAT1815RQYRMAT3025RQYRMAT3030获取报价 →参数对比 →咨询工程师 →
检测与验收
- 取样、制样、检测、复核与验收判据。标准作业流程示值误差用多齿分度台或角度块比对检定现场直线度按最小条件法评定,平面度按对角线法或网格法采集后由软件拟合验收判据用标准块间接检定:工作面均布不少于 5 点,示值误差与重复性需满足相应检定规程。注意事项班前用标准块校验,保持压头与试样表面清洁,测量系统定期用标准刻线尺校准。常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard
- an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement
- we provide a test report together with the recommended configuration.相关机型RQYRMAT1510RQYRMAT1815RQYRMAT3025RQYRMAT3030获取报价 →参数对比 →咨询工程师 →
常见问题
RQMC030-ZJPX300 的报价与交期是多久?
RQMC030-ZJPX300 可以先寄样实测吗?
出厂随机附带哪些资料?
能否按工件定制夹具或扩展量程?
售后响应与培训如何安排?
交付与服务
- 主机一台(全新原装)
- 标准附件与工具组
- 说明书、合格证、装箱单
- 出厂校准证书
- 标准出口木箱包装
- 全国物流 3–7 天送达
- 工程师上门安装调试
- 现场操作与保养培训
- 整机质保 12 个月
- 故障 48 小时内响应
- 每年一次免费巡检
- CNAS 第三方校准代办
把工件与检测要求发给我们
工程师 1 个工作日内回复选型方案、配置清单与报价。