点击查看大图RQSEF681D
SEF681D表面粗度轮廓形状测定机采用数字式轮廓形状检出器,高分解能、高精度。
- ✓原厂校准证书
- ✓12 个月质保
- ✓全国安装调试
- ✓支持非标定制
产品介绍
· 采用数字式轮廓形状检出器, 高分解能、高精度。 · 表面粗糙度检出器与高精度轮廓形状检出器可更换型—体机。 · 附有JCSS校正证书。 · 检出器自动停止保护功能。
从物理效应到测量结果,讲清设备的工作原理。压头物镜试样光源数据处理原理要点金刚石触针以恒定测力划过表面,传感器将垂直位移转换为电信号,经滤波分离粗糙度、波纹度与形状误差圆度仪则使工件或传感器绕精密主轴回转,采集径向偏差并作傅里叶分析常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement; we provide a test report together with the recommended configuration.相关机型RQXZ-150RQXZ-150GRQXZ-230RQ-PROF-490获取报价 →参数对比 →咨询工程师 →
技术规格
| 表面粗度 | |
|---|---|
| 测定范围 | 1200µm |
| 最大测量距离 | 100mm |
| Z方向分解能 | 16 bits/Range |
| 直线度 | 0.15µm/100mm |
| 触针 | R2 µm/60° |
| 轮廓形状 | |
| 测定范围 | 60mm |
| 最大测量距离 | 100mm |
| Z方向分解能 | 0.025µm |
| 直线度 | 1.0µm/100mm |
| 触针 | SB-610 |
以上为标准配置参数。特殊量程、精度、夹具或软件接口可按工件定制,工程师 1 个工作日内给出配置清单与报价。
选型指南
- 按工况对应推荐系列,再与工程师确认具体配置。工况推荐系列选型理由仅测粗糙度选手持/台式粗糙度仪以上参数仅供参考,最终配置、价格与交期以正式报价单为准。需测轮廓形状(台阶、圆弧)选轮廓仪以上参数仅供参考,最终配置、价格与交期以正式报价单为准。回转体形状精度选圆度/圆柱度仪以上参数仅供参考,最终配置、价格与交期以正式报价单为准。大口径或大工件选便携式或大型落地机型。以上参数仅供参考,最终配置、价格与交期以正式报价单为准。常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard
- an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement
- we provide a test report together with the recommended configuration.相关机型RQXZ-150RQXZ-150GRQXZ-230RQ-PROF-490获取报价 →参数对比 →咨询工程师 →
检测与验收
- 取样、制样、检测、复核与验收判据。标准作业流程用标准粗糙度样块(如 Ra 0.4/1.6/6.3)校验示值圆度仪用标准球/标准圆柱校验主轴回转误差,放大倍率需定期标定验收判据用标准块间接检定:工作面均布不少于 5 点,示值误差与重复性需满足相应检定规程。注意事项班前用标准块校验,保持压头与试样表面清洁,测量系统定期用标准刻线尺校准。常见问题How do I choose the right configuration?Send us the specimen material, dimensions and applicable standard
- an engineer will propose the model and fixturing, and provide a written selection proposal.Are the published specifications final?They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.Do you support sample testing?Yes. Send samples for measurement
- we provide a test report together with the recommended configuration.相关机型RQXZ-150RQXZ-150GRQXZ-230RQ-PROF-490获取报价 →参数对比 →咨询工程师 →
常见问题
RQSEF681D 的报价与交期是多久?
RQSEF681D 可以先寄样实测吗?
出厂随机附带哪些资料?
能否按工件定制夹具或扩展量程?
售后响应与培训如何安排?
交付与服务
- 主机一台(全新原装)
- 标准附件与工具组
- 说明书、合格证、装箱单
- 出厂校准证书
- 标准出口木箱包装
- 全国物流 3–7 天送达
- 工程师上门安装调试
- 现场操作与保养培训
- 整机质保 12 个月
- 故障 48 小时内响应
- 每年一次免费巡检
- CNAS 第三方校准代办
把工件与检测要求发给我们
工程师 1 个工作日内回复选型方案、配置清单与报价。